无数据
Company News
    Contact us
    Company News
    Position:Home > Company News

    Why choose baking booth

    Source:      2018/3/27 13:08:41      Click:

    Why choose automobile paint baking room?Because car paint baking room have the following 

    advantages:
    1.Previous processing fast, effect pride:: car paint baking room is a set of large 

    equipment. Before using the car, commonly pass prophase processing. So this not only free  

    defects of artificial processing, improve work efficiency and can improve the car paint 

    quality in repair operations. This not only for baking room can operate according to the 

    personnel Settings make paint uniform temperature and rapid drying, and baking booth can 

    isolate external dust and pollutants caused by pollution to car lacquer, so that can save 

    the follow-up of polishing processing work.
    2.Good work environment:Automotive paint baking room in order to maintain the cleanness of 

    paint room air, various types of baking booth are equipped with filtering device, such as 

    filter cotton, used to filter into the baking booth of air in the dust, and baking booth 

    ventilation systems can make paint room have enough ventilation speed, so as to ensure room 

    air clean paint. Lots of the time, the pollution of car body paint surface is caused by man

    -made factors, such as the vehicle to paint without thoroughly clean came into baking booth, 

    or spray paint personnel did not wear special protective clothing, or baking room not 

    cleaning, etc.
    3.High efficiency, quality is guaranteed:Compared with artificially spray paint, coating, 

    vehicle baking finish room is mechanization baking booth service, high work efficiency is 

    over  several times, even a few times. Moreover, when painting, external air filtered 

    through the fan primarily to the roof, and then after the top screen that is the second 

    filtration purification enter the room. Room air adopts full drop type to 0.2-0.3 m/s speed 

    down after spray paint flow to make the mist in the air particles cannot stay, and direct 

    the outlet through the bottom is expelled room outside. This constant circulation 

    conversion, make room air 98% cleanness,the air has certain pressure and can form a 

    constant airflow around the car to remove excess paint, thus maximize paint quality. Paint 

    surfaces smooth and without impurities, polishing degree is high.
    4.High safety coefficient:Automotive paint room is generally equipped with constant 

    temperature controller and safety explosion-proof system. Car lacquer, transfer the air door 

    to paint position,heated-air circulation, the temperature rise to a predetermined drying 

    temperature (55 to 60)). Fan will filter external fresh air, and after happening heat 

    exchange with  thermal energy converters,the air was sent to paint heat the gas chamber of 

    the roof, and then after the second filtration purification, hot air circulation within 

    through applications in the role, in addition to breathe in a few fresh air outside, most of 

    the hot air continue to be heated , makes the paint temperature gradually rise. When the 

    temperature reaches set temperature, burner automatically stops; When the temperature 

    dropped to set temperature, fan and burner automaticly open, make paint room temperature 

    remained relatively constant.Finally, when baking time reach a set time, baking booth 

    automaticly shut down, paint construction completely end.

    Automotive paint baking room correct use and the matters needing attention:Some vehicles,

    after baking in coating and baking room, there will be some hemp dot on the lacquer face , 

    carefully observe you will find,they are  some dust particles  packaged with paint and 

    attached to the lacquer face. When appear this kind of circumstance, illustrate that the 

    paint room of air contains a lot of dust.
    (1)Into baking booth, air is the main source of pollutants. When baking booth is not in 

    use,  the door should be shut ,the door of baking booth is strictly prohibited in open 

    state for a long time. In many repair factories, the burnish work of lacquer putty is often 

    operated in the area close distance of baking booth. In the process of grinding putty,it  

    will produce large amounts of dust, with the air flow,a lot of  putty easily come into the 

    baking booth. If lacquer putty burnished with a clean dry grinding technology, the situation 

    will be relatively better;If it is taken manually polish method, pollution will be very 

    serious. Therefore, in many repair factories, the burnish work of lacquer putty is often 

    operated in the area close distance of baking booth.
    (2)Baking booth work, draft  fan will pumped in outside air, blowing down from the top 

    cotton of spray booth,air is pumped from  paint room floor and the baking room made a 

    downdraft. So, even though there is little dust in  the baking finish room,it also won't 

    flying up. Baking booth ceiling filter cotton can filter out most of the dust, to keep the 

    into air clean. Therefore, should replaced periodically baking booth filter cotton and paint 

    baking room floor adsorption cotton.
    (3)However, spraying vehicle itself is usually the biggest polluter of paint room. Wheel, 

    fender-guard and engine compartment area will gather many contaminants; body-cleaning work 

    can make these pollutants reduce the influence of paint operation. Therefore, car body 

    cleaning and good preparation is very important.
    (4)Spray paint the operating personnel wearing clothes is also important sources of 

    contamination. In many repair shop,Burnish putty and spraying the paint job is completed by 

    the same person,when burnishing  putty and spraying  paint, many workers wear the same set 

    of overalls, this is not correct. Spraying paint should be equipped with special overalls. 

    In baking finish house, workers should wear no fiber shedding uniform, wear rubber gloves, 

    protective masks and respirator,each word paint in spray painting must keep this dress. Do 

    not wear special clothing ,no entry into the spray room , but people can only watching paint 

    homework from peep window , lest contaminate paint.
    (5)In addition to covering car-body and coating must be completed in baking room, car body 

    preparations and paint redeployment should be outside the baking booth. Some repair 

    factories even clean vehicle or burnish putty in baking room, this is a serious breach in 

    pairing and coating operation norm practice.
    (6)Spray gun etc spraying equipment must keep clean. After each homework, clean the spray 

    gun timely, lest the within gun paint drying, Paint dry hind can coagulate piece, if drying 

    sections of paint fly out ,this will  form defects.